ImageVerifierCode 换一换
格式:DOC , 页数:15 ,大小:136KB ,
资源ID:1709626      下载积分:12 文钱
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝    微信支付   
验证码:   换一换

加入VIP,省得不是一点点
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wenke99.com/d-1709626.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录   微博登录 

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(The innovative design for automobile EPS system Based on Active front―wheel steering technology.doc)为本站会员(gs****r)主动上传,文客久久仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知文客久久(发送邮件至hr@wenke99.com或直接QQ联系客服),我们立即给予删除!

The innovative design for automobile EPS system Based on Active front―wheel steering technology.doc

1、1The innovative design for automobile EPS system Based on Active frontwheel steering technologyAbstract. To improve vehicle driving safety and steering performance, analyzing the mechanical structure of the electric power steering (EPS) systems and active front steering (AFS) system and working prin

2、ciple. The new electric power steering system integration active steering technology is presented; the conventional electric power steering system is used in active front steering system. The new EPS system was composed of traditional electric power steering installation dual planetary gear and moto

3、rs around the corner. Not only needed to provide power steering, but also did through the front wheels compensation angle in driving conditions to change the angle transmission ratio, eliminate the interference between the active front steering and driver. Keywords: Electric power steering; active s

4、teering; planetary gear; variable transmission ratio 1. Introduction Driving safety, environmental protection, adjustment assembly simple and low cost are Electric Power Steering 2(EPS) advantages, it represents the future development direction of automotive power steering technology. Active front s

5、teering system is developed by BMW (Active Front Steering, AFS) can independent drivers operating. The front wheel angle and the steering gear ratio are changed by additional angle for the front wheels 1. The stability control of vehicle is achieved by turning interfere, the vehicle safety, flexibil

6、ity and driving pleasure are improved a whole new level. For a new electronic control unit, using some intelligent control strategies and control algorithms and other electronic integrated control systems to improve its performance significantly, it is a bite problem to be solved in the automotive a

7、ctive safety research. Considering steering portability, stability and security, in addition to, the AFS system is collocated, the cost is increased. How to make EPS integrate active steering function is studied based on control characteristics of EPS power, damping, and return. A new type EPS syste

8、m integration active steering is designed. On the basis of traditional EPS structure, a set of dual planetary gear mechanism is assembled turbine worm and AFS actuators is equipped. The new system can provide power, then applying a secondary angle for front wheel 3in the process which does not depen

9、d on the drivers and changed rotation ratio in real time. The dynamic control signals yaw rate and sideslip angle are introduced in the new EPS system , combining it with the ideal reference model, using robust control, fuzzy control theory to get steering torque correction , Thus, the better perfor

10、mance is achieved rely on traditional EPS power steering motor, while the Active Steering Function is achieved by active steering angle motor .improving the stability and active safety of the vehicle in separate road adhesion coefficient, large lateral forces and cornering brake extreme operating co

11、nditions. 2. Vehicle attitude control strategy based on AFS 2.1 Phase delay compensation strategy based on yaw rate The 2-DOF motion state of the vehicle is shown in Figure 1, It consist of the center of gravity velocity V, the vehicle body slip angle of gravity . the tire model of front and rear is

12、 simple linear. Figure 1 four wheel model and two wheel model Steering characteristics and suspension performance will affect the control characteristics of the vehicle. As shown in Figure 2, cyclical fluctuations at speed V = 60km /h about 1000kg, 2000 kg respectively. 4From Figure 2 we can know, t

13、he body weight increase would have a negative impact on car yaw rate, heavy body make left and right steering unresponsive. So the front corner is needed compensation in real-time. Figure 3 shows that the AFS system compensates control charts for yaw rate based on the feedback delay. Figure 3 AFS co

14、ntrol system schematic Dashed line in Figure 2 shows that the frequency characteristics, which uses the AFS system and quality of 2000kg, the feedback coefficient1. The figure shows that the speed of vehicle steering response and cornering stability are improved significantly. Therefore, EPS and AFS

15、 integrated control can provide assistance and change steering ratio. At the same time, it is not depend on the drivers to provide additional angel for the front wheels, the steering portability and stability are coordinated reasonable, driving safety and comfort are improved. 2.2 Model EPS mechanic

16、al structure integration of AFS function Electric Power Steering system is power-assisted steering systems which depend on the electric motor directly. Driving safety, environmental protection, adjustment assembly 5suppleness and low cost are its Advantages. It represents the future direction of aut

17、omotive power steering technology. First practical was equipped on a light vehicle in 1998, input torque were enlarged. Then, with the speed is change, the gain ratio is change. Later, some intelligent algorithms which develop from modern control theory can get a better sense of the road, back to th

18、e positive damping. Figure4 EPS schematic Internal construction of EPS steering apparatus is shown in Figure 4. The steering system is mainly composed of mechanical system, the torque sensor, a vehicle speed sensor, a speed reduction mechanism, motor and power electronic control unit (ECU). When the

19、 vehicle is steering, the electronic signals are detected by torque sensor and vehicle speed sensor, which sent to the electronic control unit ECU. Then the control unit analyzes and computes the data to determine voltage signal of the booster motor, a directive is issued to the motor, the output to

20、rque of motor is achieved power steering2. 1) The relationship between the compensation steering angles is provided AFS and the corner is inputted wheel is introduced. The joint control system consists of three different structures EPS and AFS is designed, as shown in Figure 5. 62) The power steerin

21、g apparatus are installed only one motor for providing additional power steering and front wheel angle. The module is integrated in EPS controller which controls the front compensation corner. 3) On the basis of the mechanical structure, a planetary gear and active steering motor are connected; comb

22、ining with the regulation of power torque in the EPS system and the angel is attached to front wheel. Steering torque and additional steering angle of the front wheels are regulated, so the active steering is achieved. The mechanical connection of the original structure is canceled. Transmission of

23、power, angle are rely on sensors to achieve power steering, it is called steering by wire. Figure5 EPS Schematic diagram integration AFS 3. The control performance of EPS and AFS joint based on single-motor 3.1 Taking AFS brakes as the controller Without changing the original structure of the EPS sy

24、stem,this structure is used mechanical parts connect, high reliability. Firstly, the new controller joint EPS and AFS is conducted performance tested. Considering the rigidity K of steering system, through the 7transfer function test only considers the steering torque increase input driver operation

25、 experience. In addition, AFS control module whether or not it can calculate the additional front wheel angle timely and accurate at high speed conditions. The model of joint control system is shown, which the dotted line show the drivers steering operation. C1 module of EPS controller determines th

26、e operating feel of the system. EPS was originally designed; it makes the output of the auxiliary torque times the input of torque sensor. if the transfer function from Tm to f is linear, output angle of AFS controller C2 and EPS power motor generated by the torque will make it achieve active steeri

27、ng .Assuming that the speed, type of road surface condition, tires raised under different parameters will not cause large changes, the linear model is built. However, the actual controller model is non-linear, correctly identification each parameter is indispensable condition to calculate the attach

28、 angle. 3.2 The non-interference problem of AFS and the reaction force In addition to the steering wheel torque input when the car turned, the steering wheel angle and damping are feedback input for control. Qualitative considerations additional output steering angle of AFS effect the drivers 8steer

29、ing. Whether the feedback torque changes caused by AFS action or irregular surface can interfere with the drivers steering input, which usually require restraining. Therefore, AFS may influence the operation of the driver, or because instability of the steering wheel, the output of AFS is designed m

30、ust be distinguished from the drivers operation, and non-interference. The transfer function from to the angle of the handle is Noninterference formula AFS control system with the operation of the driver steering; (1) However, the transfer characteristic of the controller is 0, it is not the designe

31、d. For decoupling, the additional steering torque and steering angle are needed controlled independently. Therefore, an independent motor will not provide power separately. 4. The new EPS is designed based on differential mechanism and two motors 4.1 Variable transmission ratio of new EPS system is

32、designed The studies have shown that the steering compensation angle of AFS system will produce interference with help power. New 9EPS system based on active front steering technology requires two motors in structural design, which provide front wheel compensation angles and power. Two motors and pl

33、anetary gear mechanism are used in conventional steering system, analyzing the gear mechanism and designing the nonlinear variable transmission ratio. Usually, the characteristic curve of gear ratio with the speed change can indicate the variable transmission ratio features of AFS. It divides into t

34、wo properties of linear and nonlinear models. Nonlinear transmission ratio can fully coordinate the relationship of speed, different steering input angle and corner; it is an ideal aid corner characteristic curve. The formula of additional front-wheel angle based on non-linear variable ratio: For th

35、e transmission ratio with the speed change process is smooth and natural, fitting the curve to obtain the desired angle characteristic curve. (3) Where, ig = g / f is the gear ratio of rack and pinion steering; Kr is stability factor; R is steering gear ratio; s is the input angle of steering wheel.

36、 The following figures show the simulation curve before and after optimization: 10Figure 7 shows that the curve of the corner additional angle, steering wheel angle and drive ratio in the actual steering process before optimized. Form the figure can be see , the drive motor speed is changes frequent

37、ly within a given range of parameters (10 R 20,0s180) , the variation range of front wheel additional angle which come from motor is -3,6. Figure 8 shows that a change in surface area in the actual driving process, the speed of the drive motor is in the frequent change. Within a given range of param

38、eters ( ) , the range of front additional angle which provide is -20, 30. 4.2 EPS controller is designed The control schematics of new EPS system: Fig.9 EPS control with two motors and a planetary gear There is a difference between the wheel turning angle and the operation angle because the internal

39、 gear (C) angel. Actually, the angle is boosted by planetary gear 1: N gear ratio, as shown in equation (13) ; (4) Usually, controlling the motor to achieve steering , the differences of the control angle and steering angle is changed, so C = 0. The motor 1 and the distortion rod of Figure 6 have the same effect. Through a PI controller to

Copyright © 2018-2021 Wenke99.com All rights reserved

工信部备案号浙ICP备20026746号-2  

公安局备案号:浙公网安备33038302330469号

本站为C2C交文档易平台,即用户上传的文档直接卖给下载用户,本站只是网络服务中间平台,所有原创文档下载所得归上传人所有,若您发现上传作品侵犯了您的权利,请立刻联系网站客服并提供证据,平台将在3个工作日内予以改正。