机械英语证书考试(PEC)辅导-机械专业术语.doc

1、 Mechanical Engineering English CertificationMechanical Terms Glossary A A-Arm - A suspension linkage formed in the shape of an “A“ or “V“ found commonly on the front suspension. The sides of the two legs of the A-arm are connected to the chassis by rubber bushings and the peak of the A-arm is attac

2、hed to the wheel assembly. In this way, the wheel can freely move up and down. Sometimes there is an upper A-arm, a lower A-arm, or both upper and lower A-arms. The British call it a “wishbone.“ Accelerator - Fuel pedal or throttle. A foot-operated pedal or hand-operated lever connected by linkage o

3、r electronics to control vehicle speed. Adaptive Automatic Transmission - Some transmissions can “learn“ and adapt to the drivers style, altering shift points and other transmission functions to produce the most efficient operation. Adaptive Cruise Control - One step beyond cruise control, adaptive

4、cruise control uses a radar sensor mounted in the front of the vehicle to maintain a safe cruising distance between your vehicle and the vehicle in front of you. Most systems allow you to set the interval (distance between vehicles) and will then accelerate and brake (within reason) to maintain that

5、 interval. In many cases, the systems can take into account hilly terrain and passing situations. All have the ability to act like regular cruise control, and they still require the driver to steer the vehicle normally. Some automakers refer to it as “intelligent“ cruise control. Adjustable Suspensi

6、on - Provides better ride or handling. A variety of systems are used to vary shock-absorber firmness. Some automatically sense road conditions and adjust shock-absorber settings accordingly. Others include a switch on the dashboard or console that allows the driver to adjust shock-absorber settings

7、to provide a softer or firmer ride, or sharper handling. Aftermarket - All products and services used in the repair and maintenance of vehicles that was not produced by the original vehicle manufacturer. Alternator - A component of the electrical system, it converts 12-volt DC (Direct Current) from

8、the battery into AC (Alternating Current) at the rate of 13.8 to 14.2 volts. The alternator also provided electric power to operate the engine and accessories Air Bag - The air bag, also known as a Supplemental Inflatable Restraint System, is a passive safety device, supplemental to safety belts, th

9、at inflates to provide a cushion to absorb impact forces during moderate to severe frontal collisions. This system can help to lessen the chance of contact with the steering wheel, instrument panel and windshield. The air bag is actuated automatically by sensors located in the front of the vehicle.

10、To maximize effectiveness, seat and shoulder belts must always be used in conjunction with this system Air Filter - A particulate air filter is a device composed of fibrous materials which removes solid particulates such as dust, pollen, mold, and bacteria from the air. Air Gap - Space between the s

11、park plug electrodes, also known as gap, often adjusted to gain maximum performance. Airfoil - An aerodynamic device designed to improve traction by increasing the downforce on the vehicle. The use of airfoils (also called wings) increases the cornering capability and improves stability at speed, bu

12、t often at the expense of additional aerodynamic drag. Air Injection - A system that injects air into the exhaust ports of the engine for combustion of unburned hydrocarbons in the exhaust gases, thus producing “cleaner“ exhaust emissions. Air Suspension - Instead of steel coil or leaf springs, some

13、 vehicles have a bellows-like unit at each corner that contains pressurized air. As a rule, air suspensions can produce a softer ride. Alignment - Angles of the tire and suspension axis relative to each other and the ground: camber, caster, toe. Also, the adjustment of components to bring them into

14、a predetermined position for the most efficient operation of wheel and vehicle for proper even tire wear. Alpha-Numeric - A load-based tire sizing system containing the load capacity, type of tire construction, aspect ratio, and the rim diameter in inches. Anti-Lock Brakes (ABS) - Helps maintain con

15、trol in emergency stops. Particularly useful on slick pavement. While the driver applies steady pressure to the brake pedal, the system automatically “pumps“ the brakes many times per second to prevent wheel lock-up. Anti-Roll Bar - A steel bar, linking the left and right side of a suspension. It co

16、mes into play during cornering. As the car leans in a turn, the anti-roll bar resists this leaning by transferring more weight to the outside tire. It provides a means to achieve good handling from stiff roll resistance while maintaining a comfortable ride through soft springs. Antiskid System - Hel

17、ps maintain control in fast turns. Works whether or not the brakes are applied. Sensors automatically apply individual brakes to prevent a sideways skid. Some systems also cut back on the throttle, slowing the engine. Its also known as an electronic stability system or stabilization program. A-Pilla

18、r - In the side view, the foremost roof support of a vehicle, located in most instances between the outer edge of the windshield and the leading edge of the front door upper. Also known as an A-Post. Alloy Wheels - A generic term used to describe any non-steel road wheel. The most common alloy wheel

19、s are cast aluminum. Technically, an alloy is a mixture of two or more metals. These wheels are known for their light weight and strength. Alternating Current (AC) - Flow of electricity that periodically reverses direction. All-Wheel Drive - Often confused with Four-Wheel Drive (4WD), this drive sys

20、tem features four, full-time active drive wheels to reduce wheel slippage and provide greater driver control over the vehicle. All-Wheel Drive automatically splits engine torque between the front and rear wheels as needed, improving on-road traction in unfavorable road conditions. Unlike Four-Wheel

21、Drive, All-Wheel Drive is an on-road system and is not designed for off-road use. AWD does not require the driver to actively engage the system. It is operational at all times, and requires no switches, lights or visor instructions for system operation. Ampere - After Andre-Marie Ampere, French (177

22、5-1836). The ampere is a unit of electrical current, or the flow of electricity. Anti-Lock Brake System (ABS) - On a vehicle equipped with Anti-Lock Brakes, the wheels are equipped with speed sensors. When a sensor determines that a wheel is decelerating so rapidly that lockup may occur, the electro

23、-Hydraulic Control Unit (EHCU) is activated. The EHCU then modulates the brake pressure in the appropriate brake lines by means of the solenoid-operated valves. This is intended to prevent wheel lockup and help the vehicle maintain directional stability during potentially hazardous braking situation

24、s. (See also: Rear-Wheel Anti-Lock and Four-Wheel Anti-Lock.) Antifreeze - An additive that lowers the freezing point of a liquid Aspect Ratio - The dimensional relationship between tire section height and section width; section height divided by section width. A.T.D.C. - After top dead center Autom

25、atic Climate Control - A heating and air conditioning system that adjusts itself as needed, to maintain a pre-set temperature. Automatic Locking Front Hubs - Found in some four-wheel drive vehicles, this allows the driver to engage, or “lock,“ the front axle hubs without leaving the vehicle. Automat

26、ic Transmission With Manual-Shift Capability - Allows manual gear changes, when desired, in an automatic transmission. Functions as a traditional automatic transmission when left in Drive, but includes a slot in which the shift lever can be moved to change gears manually. Sometimes, buttons for shif

27、ting manually through the gears are located on the steering wheel. This affords some of the advantages of a manual transmission, such as greater control of engine speed for better throttle response, but eliminates the need for a clutch pedal. Axle - A cross support of a vehicle on which its road whe

28、els turn. Axle Ratio - The ratio between the rotational speed (RPM) of the drive shaft and that of the driven wheel. Gear reduction in final drive is determined by dividing the number of teeth on the ring gear by the number of teeth on the pinion gear. B Backspacing - The measurement from the back o

29、f the bolt pad to the back edge of the rim; used to calculate offset and determine where the back of the bolt pad is located in relation to the rim width, sometimes referred to as rear spacing. Balance - A uniform mass distribution of a tire and wheel assembly about its axis of rotation. Ball Joint

30、- A ball-and-socket connection that lets a steering knuckle move in several directions at the same time. Bead - The area of the mounted tire which seats against the wheel. Bead Seat - The position where the tire rests and seals on the inside of the rim. Belted Bias Tire - A bias tire with additional

31、 reinforcing belt(s) between the casing plies and the tread Block Heater - An accessory which uses electric power to keep an engine thats been turned off from becoming too cold, which makes it hard to start in extremely cold climates. Bias Tire - A tire built with two or more casing plies, which cro

32、ss each other in the crown at an angle of 30 to 45 degrees to the tread centerline. Biodiesel - Refers to a vegetable oil, or animal fat-based diesel fuel consisting of long-chain alkyl ( methyl , propyl or ethyl ) esters . Biodiesel is typically made by chemically reacting lipids (e.g., vegetable o

33、il , animal fat ( tallow ) with an alcohol . Biodiesel is meant to be used in standard diesel engines and is thus distinct from the vegetable and waste oils used to fuel converted diesel engines. Biodiesel can be used alone, or blended with petrodiesel. Blemish Tire - A tire with a cosmetic or minor

34、 uniformity imperfection but whose safety and performance are unaffected. Bluetooth Capability - The ability of a radio system to work with Bluetooth wireless connectivity, to function in concert with a cellular phone. Bore - The diameter of an engine cylinder or bearing. Brake Assist - Designed to

35、shorten stopping distance in a “panic“ stop. Applies full braking power even if the brake pedal is not fully depressed. Sensors gauge the speed at which the driver initially depresses the brake pedal and determine whether full emergency stopping power is warranted. Brake Drum - A drum brake is a bra

36、ke in which the friction is caused by a set of shoes or pads that press against a rotating drum-shaped part called a brake drum. Brake Fade - A condition brought about by repeated brake applications, resulting in build-up of heat that causes a temporary reduction or fading of braking effectiveness.

37、Brake Horsepower (BHP) - The actual horsepower of an engine, measured by a brake attached to the driving shaft and recorded by a dynamometer. Brake Linings - The replaceable friction material which contacts the brake drum in a drum brake system to slow or stop the vehicle. Brake Master Cylinder - A

38、cylinder containing a movable piston activated by pressure on the brake pedal. The piston produces hydraulic pressure that pushes fluid through the lines and wheel cylinders. This forces the brake lining or pad against the drum or disc to slow or stop the vehicle. Brake Pads - In a disc system, they

39、 are the replaceable flat segments consisting of a rigid backing plate plus frictional lining that takes the place of the shoe and lining in a drum brake. Brake Shoe - The arc-shaped carrier to which the brake linings are mounted in a drum brake. They also force the lining against the rotating drum

40、during braking. Brakes, Disc - A type of braking system in which brake shoes, in a vise-like caliper, grip a revolving disk mounted on a wheel to slow or stop disc and wheel rotation for braking. Brakes, Drum - A type of braking system that utilizes a metal drum mounted on a wheel to form the outer

41、shell of a brake. The brake shoes press against the drum to slow or stop drum and wheel rotation for braking. B-Pillar - The roof support between a vehicles front door window and rear side window, if there is one. Bolt Circle - Often referred to as the wheel bolt pattern; the diameter of an imaginar

42、y circle drawn through the center of each lug hole. Braking Torque - Torque applied by a brake to a tire/wheel assembly, which slows or stops the vehicle. Breakaway - The point at which tire cornering traction is lost. Bumpsteer - A steering effect resulting from toe or camber changes as the suspens

43、ion moves up and down. C Caliper - In a disk brake, a housing for cylinder, pistons and brake shoes, connected to the hydraulic system. The caliper holds the brake shoes so they straddle the brake disc. Camber Angle - The inward or outward angle which a front-wheel spindle makes with a vertical line

44、, as viewed by either the front or the rear of the vehicle. Positive camber results when the top of the tire tilts out further than its bottom. The adjustment of this setting affects both tire wear and vehicle handling. Camshaft - The shaft in the engine which is driven by gears, belts or chain from

45、 the crankshaft. The camshaft has a series of cams that opens and closes intake and exhaust valves as it turns. Camber Thrust - The lateral force developed by a tire due to its camber. A force in the same direction as the leaning of the tire. Carrying Capacity - Amount of load that a tire can carry

46、at a given inflation pressure as established by the Tire and Rim Association. Cart - Championship Auto Racing Teams; sanctions races for Indy type cars. Casing (Carcass) - The structure of tire cords locked around wire beads, (most often used in relation to worn tires). Caster Angle - The forward or

47、 backward tilt of the steering axis as viewed from the side. If the point of load is ahead of the point of contact, the caster angle is positive. The caster angle tends to keep wheels in a straight line. Proper caster adjustment improves both tire wear and fuel economy. Catalytic Converter - A stain

48、less steel canister that is part of a vehicles exhaust system and contains a thin layer of catalytic material spread over a large area of inert supports. It induces chemical reactions that convert an engines exhaust emissions into less harmful products prior to entering the environment. Center of Gr

49、avity - The center balance point of a vehicle; the single point where a vehicle would be supported without tipping up or down. Centerline - A plane dividing a tire, wheel, or vehicle into two symmetrical halves. Centrifugal Force - The force that tends to throw a tire away from the axis of rotation, same as radial force. Chapman Strut - A rear suspension system which operates on the same principles as the MacPherson Strut; it uses lower links or a control arm and a long spring-shock strut. Chassis - The frame, suspension system, engine,