1、Thank you for your using air source water heater series products. Please read instruction book before use and keep it for future reference. Please record the machine model and serial number on the warranty card.Adaptive Model Number: JN-100L、150L、200L、300L.Catalog1. Cautions-2. Performance and Featu
2、res-3. Performance Parameter-4. Operation Instructions-5. Product Structure-6. Outdoor Circuit Diagram-7. Care and Maintenance-8. Simple Trouble Self-examination-9. Warranty card-1. CautionsThanks for your purchasing our products, please note the following points:a. Read this instruction book carefu
3、lly before installation!b. It shall be installed follow the rule of National TWiring Rule;Tc. Power socket shall be triplex receptacle with safe ground wire and match with the machine plug. The content shall no less than 2 times of machine rated current. The socket shall be near the machine and in t
4、he place of plug reached.d. It shall use special branch circuit that 2 times more than maximum rated current. The wire shall match to the maximum value of customer use. The circuit shall hold suitable all-pole disconnection protector (1.5-2 times more than rated current.e. The display board shall be
5、 installed in the shade dry place.f. Keep the water tank full before the power socket is connected at the first time. Please do not close the water valve at the time of normal use or it will not make the water outlet.g. Do not set over heated water as you would like to. As the water temperature reac
6、h to the 55. You should mix the cool water with hot water for being scalded (especially old man and children);h. Do not install and move the machine by yourself. All works shall be done by professional install workers.i. As the trouble made by customers, the company will not be responsible for it.2.
7、 Performance and FeaturesAir source water heater is usually used in the places of family house, bathing spot and hotel. The main advantages as follows:Energy Conservation Compare with general water heater, it holds lowest operation costs. It is lower than electrical solar water heater in the whole y
8、ear. Environment Protection Free from contamination. It use new type refrigerant that zero emission onto ozonosphere. Besides that, it does not make any excreta. All-weather Does not be influenced by bad weather such as overcast and rainy and snow. It could normal be used among -1043. It works effec
9、tively in dry and wet places with Intelligent defrost system. Reliable Quality Use well known best quality special compressor, food grade stainless steel tank. It could be used for more than 15 years under normal use. Safety Real completely separated water from electricity; Convenient Easy installat
10、ion and smaller floor space. It could be installed in a suitable places and content the requirement of customers.3. Performance ParameterNote: Heat water compensation speed is tested in the condition of 20 Wet-bulb temperature, 20inlet water temperature, 55leaving water temperature. This list parame
11、ter is for reference only. Detail parameter is subject to the machine brand.Model No. JN-100L-30W JN-150L-30W JN-200L-40W JN-300L-40WTank Volume(L) 100 150 200 300Heat Speed(L/h) 75 75 95 95Max Leaving Water Temp ( ) 60Power 220V/50HzRated Input Power (W) 940 1280 1280 2000Tank Bearing Pressure 0.6M
12、pa Temp Range() -10 43 Tank Weight (kg) 26 36 46 65Tank Out Size 4801074 4801514 5701300 5701835Machine Weight (kg) 27 36 36 45Machine Out Size 790*255*540 790*255*540 790*255*540 790*255*540Suited People 13 24 24 Above 44. Operation Instructionsa. Temperature Display: the controller shows the water
13、 temperature in the tank. Press “ ”, it will show the outside temperature.b. ON/OFF: Press “” to ON/OFF machine. As in the conditions of ON, it shows “heat”, “heat insulation”, “defrosting”. It shows “OFF” while the machine is power off. Whenever the condition is, it always shows the present time an
14、d present temperature.c. Temperature Setting: Press “S” and get into the temperature setting condition. As it shows the “ceiling temperature”, press “” or “” to change the value (press “” to raise 1, press “” to fall down 1; hold “” or “” for more than 0.5 second, it will raise and fall down quickly
15、). Press “S” again and the floor temperature setting method follows ceiling temperature. As setting finished, press “” once again to go back from setting condition. It will begin to work as the temperature lower than the floor temperature or higher than ceiling temperature and make the water tempera
16、ture between “floor temperature” and “ceiling temperature”d. Time setting: press “”, the hour part will be shining, press “” or “” to adjust the hour part; press “” again to adjust the minutes part, press “” once again to finish.e. Operating Mode Setting: Press “M” and shift “Automatic” to “Economic
17、”. Under the “Automatic” model, it will control the water temperature according to the pre-setting. Under the “Economic” model, only make the water hot in the pre set time.f. Work Period under Economic Model Setting: hold the “” for 2 seconds and set three heat period as screen shows. (“” is used fo
18、r switch the project, “” or “” is used for value change). If you do not need so many setting period, you could make the start time and finish time on “00:00”. If the start time is later than finish time, it will consider that the finished time is on the next day. For example: if you set the one of t
19、he period on “22:00” to “03:30”, the machine will consider the period is start from 22:00 and finish in 3:30 next day.5. Product Structure(Fig 1)6. Outdoor Circuit DiagramNote: Non-professionals are not allowed to change! 7. Care and Maintenance For long time work, there is some dust on heat interch
20、anger aluminum foil. It shall be brushed with water regularly or it would have effect on heat absorption. As there are great amount of dust, please let professionals clean. Check the connect end is leak or not regularly. Please contact the professionals to repair it if it is leak. Check the wire is
21、plug, socket and wire is well connected or not regularly. As the machine has some informal noise, you should power off it and contact the professionals.Healthy SymptomThe symptom as follows does not mean something had happened to the machine:a. For the compressors defective function, the machine doe
22、s not start for 3 minutes.b. There is some condensed water discharged from the outdoor machine.c. Some noise in the machine. As the machine worked, there is some bicker or sizzle noise. It is a normal noise from refrigerant.d. For safety valves pressure relieve function, the valve will discharge som
23、e water to relieve as the water tank get overpressure. 8. Simple Trouble Self-examinationFault Display Fault CauseShow “OPE” Open circuit on water tank test line or outside machine test lineShow “ SHR” Short circuit on water tank test line or outside machine test lineShow “Drop” Communication failur
24、es between display panel and outside control boardShow “leakage” Machine electric leakageAlarm on failures defrostingDuring the settled time, machine temperature could not reach to the settled defrosting temperature.Alarm on high temperature The temperature is 10 higher than ceiling.Symptom Fault Ca
25、use SolutionMain power does not be connectedCheck up on both incoming line and air switchThe control panel does not open Press the “ON” keyCompressor does not workFault code on drive-by-wire controllerCheck follows the code tableCan not reach to the setting temperature for long time heating.Dust on
26、heat interchanger, the ambient temperature is too cold, refrigerant is dischargedClean the heat interchanger; improve the environment; check on leakage point, supplement some refrigerantMain power does not be connectedCheck on incoming line and air switchNo words on the display panel Poor contact on
27、 signal wireCheck on signal wire and fittingsFour-way valve or four-way valve loop is brokenReplace four-way valve or four-way valve loopCan not make hot water and the main machine blows hot wind Wiring harness is loose Keep the line be connectedEither fan or capacitance is broken Replace fan or cap
28、acitanceFan can not workWiring harness is loose Keep the line be connectedBig noise as the machine workFrame screw loose screw down screwSome copper pipes touched each other in the machineCheck on the copper pipesNote: 1. The test or disconnect failure will be solved as both test and communication a
29、re recovered. 2. The high temperature alarm will be discharged as the water temperature drop to the normal.3. There are some ways to solve the problem of defrosting failure as followeda) The outdoor machine temperature is higher than defrosting start temperature.b) Press “” key to close the machine.
30、9. Warranty cardWarranty card (Please send affiliated card to us and reserve the original card)In order to keep our service promise and release customers from worries, we will establish customer info file in our company computer system. Please complete the warranty card and send our the affiliated c
31、ard in one month If the original card or purchasing proof is missing, you could look up your customer info file and get some related service.a. Products InfoPurchase date Purchase PlaceModel. No.Factory NumberPurchase priceb. Customer InfoName JobZip Code Phone NumberAddressNote: please tear out thi
32、s part and send it to us as follow requirement (copy here of is invalid)Please fill this warranty card and send us the affiliated card as soon as possible.Please fill this warranty card and send us the affiliated card as soon as possible.Zip Code:AddressAfter service DepartmentWarranty card (Reserve
33、 the original card) To shops: this warranty card is a clear proof for customers. The sales should write down the warranty card for customers and give it to customers. To customers: free repair during warranty period. Customers should keep the card. Please note that maybe there are some conditions ab
34、out exchange parts or goods.Products NameFactory NumberNO： Type No.Guarantee timeFrom Month Year in one year is valid Purchasing dateDate Month YearStore name TelAddress Zip.Customer Name TelAddress Zip.Problem & Date Repair feesPart you exchanged: Charging Methodfree/not freeGuarantee CardRepair Me
35、thod: Repair PeopleProducts NameFactory NumberNO： Type No.Guarantee timeFrom Month Year in one year is valid Purchasing dateDate Month YearStore name TelAddress Zip.Customer Name TelAddress Zip.Problem & Date Repair feesPart you exchanged: Charging Methodfree/not freeGuarantee CardRepair Method: Rep
36、air PeopleThank you for your using air source water heater series products. Please read instruction book before use and keep it for future reference. Adaptive Model Number: JN-100L、150L、200L、300L.Catalog1. Installation Instructions a. Main Machine Installation Siteb. Main Machine Installation Stepsc
37、. Temperature Hold Box Sited. Temperature Hold Box Installation Stepse. Heat Connecting Hose Installationf. Leakage Checking on Connecting Hostg. Connections of Circuitsh. Test Runningg. Remove air source1. Installation Instructionsa. Main Machine Installation Site(1) As the main machine was install
38、ed on the wall or roof, the place they installed shall be made of solid brick, concrete or other strength place. The main install place shall load more than 300kg/m2. Keep it upright and level.(2) The install face shall made of wood or metal that has enough firm. (3) The space between main machine a
39、nd obstacles shall not smaller than the space showed in (Figure 1)(4)If you install the canopy, please note that it shall not block heat absorption and dissipation of the main machine(5) The space between main machine and water tank will not longer than 2.5m (there are some length limitation on main
40、 connection host).b. Main Machine Installation Steps(1) Direct installation (With customer permission, ensure that there is no leak in expanded hole)(a) Mapping the space between the outside installation holes. Mark the pre-installed place.(b) Dig 4 M12.5 holes by impact drivers(c) Fix the outside m
41、achine by M8 steel setscrew.Thank you for your using air source water heater series products. Please read instruction book before use and keep it for future reference. Adaptive Model Number: JN-100L、150L、200L、300L.Catalog1. Installation Instructions a. Main Machine Installation Siteb. Main Machine I
42、nstallation Stepsc. Temperature Hold Box Sited. Temperature Hold Box Installation Stepse. Heat Connecting Hose Installationf. Leakage Checking on Connecting Hostg. Connections of Circuitsh. Test Runningg. Remove air source1. Installation Instructionsa. Main Machine Installation Site(1) As the main m
43、achine was installed on the wall or roof, the place they installed shall be made of solid brick, concrete or other strength place. The main install place shall load more than 300kg/m2. Keep it upright and level.(2) The install face shall made of wood or metal that has enough firm. (3) The space betw
44、een main machine and obstacles shall not smaller than the space showed in (Figure 1)(4)If you install the canopy, please note that it shall not block heat absorption and dissipation of the main machine(5) The space between main machine and water tank will not longer than 2.5m (there are some length
45、limitation on main connection host).b. Main Machine Installation Steps(1) Direct installation (With customer permission, ensure that there is no leak in expanded hole)(a) Mapping the space between the outside installation holes. Mark the pre-installed place.(b) Dig 4 M12.5 holes by impact drivers(c) Fix the outside machine by M8 steel setscrew.Note During Direct installation: It shall be permitted by customers
