1、NPT 螺纹简要尺寸管子公称尺寸in1/16 1/8 1/4 3/8 1/2 3/4 1 1 1 2 2 3 3 4in0.31250.4050.5400.6750.8401.0501.3151.6601.9002.3752.8753.5004.000 4.500管子外径mm 7.910.3 13.7 17.1 21.3 26.7 33.4 42.2 48.3 60.3 73.0 88.9101.6 114.3每英寸牙数27 18 14 11 8螺距：mm0.9408 1.411 1.814 2.209 3.175旋合长度：mm4.0644.1025.7866.0968.1288.61110.
2、160 10.66811.07417.32319.45620.85321.438旋合中径：mm7.1429.48912.48715.92619.77225.11731.46240.21846.28758.32570.15986.06898.776111.433NPT 代表美国标准管螺纹(National Pipe Tapered) ，NPTF 则是干密封式美国标准管螺纹。 两者基本牙型是一样的，不同点是： 螺纹牙高不一样。NPT 可能有过盈也可能有间隙，但 NPTF 没有间隙； NPT 内外螺纹均为圆锥，而 NPTF 外螺纹是圆锥，内螺纹则有圆锥、圆柱两种； NPT 有右旋也有左旋，NPTF
3、只有右旋一种旋向。NPTF NPTM 螺纹是什么意思？NPT：National (American) Pipe Thread 美国管螺纹。 F：Female 内螺纹。 M：Male 外螺纹。国家螺纹管标准 ANSI B1.20.1 Characteristics of NPT (also known as ANSI/ASME B1.20.1 Pipe Threads, General Purpose): 该标准规定: tapered thread 1o 47 锥形螺纹 1 度 47 分 truncation of roots and crests are flat 顶部和根部的截断面是平的 6
4、0o thread angle 60 度的螺纹断面角 pitch is measured in threads per inch 单位罗纹数以每英寸计算 Note! Pipe sizes do not refer to any physical dimensions. The outside diameter of a pipe or fitting must be measured and compared to a table for size identification. A 3/4“ NPT pipe thread has an outside diameter - OD - of
5、1.050 inches. 备注：管的尺寸不是指物理容积。管的外部直径和属性必须以下面这个表格来确定。例如：一个标准为 3/4“ NPT 的管外部直径为 1.050 英寸。 Each thread size has a defined number of threads per inch - TPI, or pitch. The 3/4“ NPT pipe thread has 14 threads per inch. Both the TPI and OD of the thread are required for positive identification of thread siz
6、e because more than one size have the same TPI. 每种罗纹管每英寸有固定的罗纹数（单位的罗纹数）。TPI 或 pitch 就是单位的罗纹数。 3/4“ NPT 标准的罗纹管每英寸有 14 条罗纹。由于不同的标准中可能会出现同样的单位罗纹数。因此每个标准必须有固定的单位的罗纹数（TPI)和固定的外部直径（OD)。 NPT - American Standard Pipe Taper Thread 1) Pipe Size 管的尺寸 (inches) Threads per Inch 单位罗纹数 TPI - pitch Outside Diameter
7、 外部直径 OD (inches) 管的尺寸 单位罗纹数 外部直径 1/16“ 27 0.313“ 1/8“ 27 0.405“ 1/4“ 18 0.540“ 3/8“ 18 0.675“ 1/2“ 14 0.840“ 3/4“ 14 1.050“ 1“ 11-1/2 1.315“ 1-1/4“ 11-1/2 1.660“ 1-1/2“ 11-1/2 1.900“ 2“ 11-1/2 2.375“ 2-1/2“ 8 2.875“ 3“ 8 3.500“ 3-1/2“ 8 4.000“ 4“ 8 4.500“ 5“ 8 5.563“ 6“ 8 6.625“ 8“ 8 8.625“ 10“ 8 1
8、0.750“ 12“ 8 12.750“ 14“ 8 14.000“ 16“ 8 16.000“ 1) The taper is 1/16 inch in an inch, which is the same as 3/4 inch in a foot (angle 1o 47) 1） 锥度为每英寸 1/16 英寸和每英尺 3/4 英寸是一样的。 NPT threads are not interchangeable with NPS - National Pipe Straight - threads. 国家螺纹管标准和美国标准直管螺纹NPT threads may look similar
9、 to ISO 7/1 threads. However, ISO and NPT threads should not be mixed. ISO threads have 55o taper angle versus 60o for NPT. The NPT root and crest configurations are also different from ISO. For ISO threads pitch is usually measured in millimeters (may be expressed in Inch). The pitch are different. 国家螺纹管标准可能会像 ISO 7/1 国际标准化组织的 7/1 标准。但请不要将两种标准混淆。国际标准化组织的 7/1 标准有 55 度的罗纹标准，而国家螺纹管标准则是 60 度。国家螺纹管标准的顶部和底部和国际标准化组织的 7/1 标准也不相同。因为国际标准化组织的 7/1 标准通常是用毫米来度量的。罗纹也不同！
