1、大管家 YA 系列电子密码保险箱操作说明书功能1、门锁：采用优质防钻锁头，防撬性能高，顺时针转动打开门锁。、液晶显示屏：采用橙、蓝双色显示屏，待机状态日历显示。3、“*”字键：清除键，数字隐含功能及修改日期、时间功能。4、应急锁：逆时针转动打开电子密码锁，顺时针关闭。5、圆盖：取下此圆盖可使用应急锁。6、“0”字键：启动进入自动报警状态功能。7、“#”字键：启动电源键，密码确认键。8、外接电源插孔：DC6 伏。9、手柄：外观流线形设计，造型美观、手感十分。10、滚轮：采用特殊材料制成，滚动省力且可拆下。使用方法：、拿下圆盖，将应急钥匙插入应急锁孔内，逆时针转动 90打开电子锁，插入门锁钥匙向右
2、转动，再向右转动手柄，拉开箱门（无手柄的向右转动门锁钥匙，即可拉开箱门）。、将节号电池按指示的正负极方向，装入箱门后盖电池盒中，接通电源后，显示屏出现“”在显示屏中下方左至右来回扫描，扫描两次后出现“good”后，显示屏熄灭，进入待机状态，拔出应急钥匙，盖好圆盖。3、待机时，显示屏显示日期、时间、星期及电压状态。电子密码设置1、 个人密码设置：开门状态下，按箱门此时显示屏出现静止光标，在 10 秒时间内输入您需要的任意 1-7 位密码，按“”字键确认，显示屏显示“”表示密码输入成功（注：输入密码时间超过秒，显示屏将熄灭，需重新开始。密码数字设计达 8 位时，将自动确认前 8 位数字为您个人新设
3、置的密码）。例：按 换码键 出现 - 输入 1234 按 # 确认，显示屏显示“In”，表示密码输入成功。2、管理密码设置：开门状态下，按“#”启动，按“00”键，再按箱门后盖板上标有“换码键”的按钮（注：在待机状态下进行）。例：按 # 按 00 按 换码键 出现 - 输入 123456 按 # 确认，显示“In”，表示管理密码输入成功。3、更改密码，方法同上（1）、（2）。日历设置1、 待机状态下，按“*”字键，进入修改日期、星期、时间状态。2 、直接按数字键，输入“年”、“月”、“日”、“星期”、“时”、“分”共 11 位数字，相应的设置位闪烁后，自动确认保存并退出设置状态，回到待机状态。
4、各个参数有效范围如下：年：0099 月：0112 日：0131 星期：17 时：0023 分：0059 3 、设置中如输入错误，按“*”字键可后退一格，重新输入正确的数字。开启/关闭开启的步骤：1、插入门锁钥匙。2、按“#”字键，显示屏显示静止光标“-”。3、新设密码输入后，按“#”字键确认。4、在 10 秒内顺时针转动钥匙到位，并向右转动手柄，拉开箱门（注：没有手柄的，转动钥匙，拉开箱门）。关闭1、手柄向左转动到位。2、门锁钥匙向左转动到位，然后拔出。3、没有手柄的向左转动钥匙到位，然后拔出即可。报警功能/隐含功能报警功能1 、错码报警：连续输入三次错误密码，则显示屏显示“Error”，并发
5、出强烈报警声，输入正确密码后即可解除报警，并出现“open”。2、振动报警：在待机状态下，按“0”键一次，显示屏显示“ALERT ON”, 并进入警戒状态，一旦箱体受到外力振动，倾斜或冲击即马上报警，同样输入正确密码后，即可解除报警，并出现“open”隐含功能为了保密起见，在使用时显示屏可只显示“”而不显示密码数字，具体操作如下：1、先按“#”键启动电源后，再按“*”，然后输入正确密码，此时显示屏只出现“”，如输入正确，即出现“open”，可正常开启。2、正常开启后，自动恢复数字显示。更换电池/应急开启更换电池本系统电源电压为 6v，采用 4 节 1.5v5 号碱性电池，当显示屏左下方电池电量
6、显示空心标志时，显示屏出现“LO-BATT”字样，则提醒电池电量不足，需尽快更换电池。应急开启1、当电池用尽无法正常开启时，请将外接电池盒装入电池，插入面板下面的外接电源插孔内供电，按正常开启方法打开箱门。2、当箱内电子密码系统发生故障或密码遗忘时，请用应急钥匙打开电子锁，并打开锁，开启箱门。注意事项1、切勿将用户使用手册、门锁钥匙及应急钥匙锁入箱内，门锁钥匙和应急钥匙应放安全的地方。2、使用时切切熟记密码并绝密。3、长期不用外接电源，应将电池从外接电池盒中取出。亲爱的用户，感谢您使用本产品！如果您有不满意的地方，请联系我们。上海大管 家保险箱有限公司 售后服务电话深圳 0755-899500
7、89 东莞076922223345 广州 02037278723 上海 021-26885388 YA Series Electronic Safe Operating InstructionsFUNCTIONS1. Lock:Adopt high quality lock, turn the knob clockwise to open the door.2. LCD display: Display in orange and blue, and show the calendar in standby mode.3. “*”Keypad: The button is used to cl
8、ear the entered combination. Hide code function, set the date and time function.4. Emergency Lock: Turn the emergency key counter clockwise to open the lock, clockwise to close.5. Emergency lock coverYou can use emergency Lock after take off the emergency lock cover6. “0” KeypadStart up into automat
9、ic alarm mode.7. “#” KeypadPower key, CODE confirmation key.8. Emergency battery box jackDC adapter(6V)9. KnobStreamline design and attractive appearance.10. Idler wheelAdopt special material, easy to roll and teardown.OPERATION PROCEDURES1.Uncover the emergency lock cover, fully insert the emergenc
10、y key into the key hole, then turn the emergency key counter clockwise (90) to open the lock; Turn right the emergency key, then also turn right the knob to open the door. (Some models without knob, Turn right the emergency key to open the door)2.Uncover the battery compartment cover on the back of
11、the door. Install four AA batteries. Pay close attention to the polarity of the batteries. When the batteries are installed, the display will flash “” and the system is actuated to scan the circuit, then show “good” after two times. And then the LCD display will wink out, into standby mode, please t
12、ake off the emergency key and put on the emergency lock cover.3. Once that is complete it will be in standby mode, while displaying date, time, week and voltage state.SET CODE1. Set user code: When the door is on opening, the display will read “”, now enter a 1-7 digit code (Enter factory preset cod
13、e 1234 or your own code if the factory code has been changed) within 10 seconds and confirm it by pressing the “#” key. Now the display will read “IN”. You have now successfully set the user code which can be used to open the door. (Note: If the setting user code time shall not exceed 10 seconds, ot
14、herwise the LCD screen will turn off automatically and the current operation will become invalid, you need to restart. When the code number reach to 8 digit, it will assigned anterior 8 digit as your new set user code automatically).Example:Press # then display - enter 1234 then press # to confirm，i
15、f the display reads “IN”.，the code confirmation is successful.2. Set management code:When the door is on opening, press #”, then press “00”, and then press the “ESC” on the back of the door.( do it in standby mode)Example:Press # then press 00 and then press ESC enter 123456 then press # to confirm，
16、if the display reads “IN”.，the code confirmation is successful.3. Change the codeDo it same as the above clause1 、2.SET THE CALENDAR1.In standby mode, press “*” key, enter into the date, week and time setting mode.2.Use the digit key to set the year, month, day, week, hour and minute. The parameter
17、availableIn is as below:Year: 0099Month: 0112Day: 0131 Week: 17 Hour: 0023 Minute: 00593.When the you enter incorrect digit, press“*”key, the digit on the display will decrease by one, then you can set the correct digit.OPEN / CLOSE Open the door 1. Insert the key into the key hole, 2. Press the “#”
18、 key, the display will read “-”3. Enter the new code and press “ #” to confirm4. Turn the key clockwise, then turn right the knob to open the door.Close the door1.Turn left the knob to lock up.2.Turn left the key to lock up, then take off the key.3.Some models without knob, just turn left the key to
19、 lock up, then take off the key.ALARM FUNCTIONAlarm1.Wrong code alarm: If the wrong code is entered 3 times consecutively, the display will read ”Error”, and raise a sharp alarm. To cancel the alarm mode and to stop the alarm from sounding, just enter the correct code and will display “open”.2.Being
20、 vibrated alarm:In standby mode, press “0” key, the display will read“ALERT ON” and in alarm state. Once it being vibrated, inclined or hit, it will raise a sharp alarm. To cancel the alarm mode and to stop the alarm from sounding, just enter the correct code and will display “open”.HIDE CODE FUNCTI
21、ONIn order to keep its safety, it just display “”, not the code digits when using.The operating procedures is as below:1.Press “#” key to start the power, then press “*” key, enter correct code, the display will read“”, if the code is correct, it will display “open”.2.When it opened, it will display the digit code then.REPLACE THE BATTERIES / OPEN IN EMERGENCY
