1、附:表面等級一覽表NON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 1 OF 38 REV* * 目 錄 * *章節 ITEM 內 容 CONTENTS 頁次 PAGE目 錄TABLE OF CONTENTS 修 訂 履 歷REVSED HISTORY 範 圍SCOPE 參 考 文 件PEFERENCE DOCUMENTS 檢 視 方 法INSPECTION METHOD 金 屬 板
2、片SHEET METAL 塑 膠PLASTICS 組 件 排 列PARTS ALIGNMENT 硬 體 與 連 接 器HARDWARE AND ONNECTIRS 貼 紙 與 商 標LABELS AND LOGOS 瓦 楞 紙 箱CORRUGATED CONTAINERS 本 文TEXT 裝 訂BINDERS 詞 彙GLOSSARY APPROVED CHECKED PERPAREDBYDATENON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSM
3、ETIC,CPU/OPTION PRODUCTS PAGE 2 OF 38 REV* * 修 訂 履 歷 表 * *版 次 ECN NO. 修訂頁次 備 注ABCDEFGHJKLMNPQRSTUVWYZNON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 3 OF 38 REV1. 範圍: SCOPE本文規範 DESKTOP.手提式伺服器(SERVER) 以及除了手提式產品所使用之面板顯示
4、器以及鍵盤等顯示功能產品以外之任何產品.This specification defines the COSMETIC requirements for DESKTOP ,PORTABLE ,SERVER ANDOPTION PRODUCTS EXCLUDINGDISPLAY SCC individual assembly drawing for cosmetic requirementsfor assemblies excluded herein.2. 參考文件: PEFERENCE DOCUMENTS2.1 應用文件:下列文件為本規範的一部分.除非特別指定,否則文件以指標或申請提案日為生效
5、日期.APPLICAB LE DOCUMENTThe following documents form a part to this specification to the extentSpecified herein. Unless otherwise indicated, the documents is of theIssue if effect on the date of invitation to bid or request for proposal.NON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主
6、題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 4 OF 38 REV2.2.優先順序: ORDER OF PRECED本文若與其製程管制項目相牴觸,則以製程管制項目為優先.In the event of a conflict between this document and the manufacturingprocess Details, The manufacturing process details shall take precedence.本文若與其製程管制項目相牴觸,則以製程管制項目為優先.
7、In the event of a conflict between this document, reference documents andpiece Part drawings, the piece part drawings will take precedence.3.檢視方法: INSPECTION METHOD3.1.目視檢測: 依下列規定檢測.VISUAL INSPECTION Inspection shall be conducted as follows.3.1.1.照明:目視檢測以工廠常態照明(10020 呎燭光之冷白螢照明光)為宜.LightingVisual ins
8、pection shall be conducted under normal shop lighting (10020 Foot candles cool white fluorescent illumination).3.1.2.位 置: position I.將待測零件置於執行檢測者面前 18 至 24 吋( 約手臂長)place the assembly or piece part 18 to 24 inches (arms length) in frontof person performing the inspection .II.應以正對檢測者及垂直於表面( 即45 角度) 兩方
9、向進行零件組件目視檢測.The assembly or piece part shall be viewed in two positions, normalto Inspector and perpendicular to the surface(45 degrees).NON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 5 OF 38 REV3.2. 退貨標準 DEFINING RE
10、JECT CRITERIA 3.2.1 直徑小於 0.01 英寸之任何瑕疵,視為看不見.Imperfections less than 0.01 inch in diameter are considered notVisible3.2.2.必須依第 3.1.2 之 II 節所規定之兩方向都看得到才算缺點.The defect must be seen in both viewing position, see section 3.1.2(II)Of this document.3.2.3.如視發現可能造成退貨之瑕疵,應參考適當等級之退貨標準.If a possible reject is f
11、ount, refer to the appropriate surface class for the rejection criteria. 3.2.4.如於目視檢測發現外觀上之可疑瑕疵,不應即冒然視為退貨拒收.Suspected rejects found while viewing outside of the establishedinspection parameters shall not be considered in the rejection of the part or assembly.3.2.5 如可能將缺陷加以分組歸類,以使組件為合格.側如:多而短小的刮痕可能稍類
12、為一處損傷,成為可接受之缺陷.Classify or group imperfections in order to make the assembly ifpossible if possible. Example. Multiple scratches could be classifiedas an abrasion and then the defect could be acceptable.3.3.表面等級之定義:Definition of classes 3.3.1.第 I 級面:第 I 級面應定義為操作人員隨時可見的區域,是外觀要求最嚴格的區域.Class I areasCla
13、ss I areas shall be defined as areas in continuous view of theOperator. Class I areas are the most critical for cosmetic requirements.例如: Desktop 型電腦之頂及正面,手提式電腦打開時Example: Desktop : top and front of computer. NON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFC
14、ATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 6 OF 38 REVLCD 及鍵盤面板,伺服器:電腦正前,顯示器:顯示器正前面,鍵盤之頂及正面邊緣. Portable: LCD and keyboard bezel of computer in view when opened.Sever: front of computer.Monitor: front of monitor.Keyboard : top and front ad edge of keyboard.3.3.2.第 II 級面:第 II 級面應定義為操作人員可偶爾看見的區域,其外觀要求不如第
15、I 級面嚴格的區域.例如:Desktop 型電腦之背面及側面手提式電腦蓋合時之頂、側面、底面及背面不屬於前節列轝第 I級面規定之所有印花紋之表面,伺服器:電腦之頂及側面,顯示器: 顯示器之頂及側面,鍵盤之側面.Class II areasClass II areas shall be defined as areas occasionally in view of theoperator, Class II cosmetic requirements are not as stringent as class I requirements.Example: Desktop : bark and
16、 sides of computer.Portable : top, sides, bottom and back of covered in view when closed, All textured surfaces not covered by class Iexamples above.Server : top and sides of computer.Monitor :top and sides of monitor.Keyboard :sides of keyboard.3.3.2.第 III 級面:第 III 級面應定義為操作人員極少看見的區域,其外觀要求不如第 II 級面嚴
17、格的區域.例如:Desktop 型電腦之底部及背面彎角及下凹部分,手提式電腦各開口孔背面以及未印花紋之表面,伺服器:電腦之背面,顯示器:顯示器之背面,底面,鍵盤之背面及底面.Class III areasClass III areas shall be defined as areas seldom seen by the operatorClass III cosmetic requirements are not as stringent as class II requirements.Example: Desktop : bottom and recessed areas on bac
18、k of computer.Portable : surfaces behind access doors and non textured Surfaces of computer. Server : back of computer.Monitor :back, base and bottom of keyboard.Keyboard :back, and bottom of keyboard. . NON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION
19、,COSMETIC,CPU/OPTION PRODUCTS PAGE 7 OF 38 REV3.3.4.第 IV 級面:第 IV 級面應定義為操作人員看不見的區域 ,是外觀要求最不嚴格的區域.例如:Desktop 電腦,顯示器及鍵盤之內面.Class IV areasClass IV surface shall be defined as areas never seen by the operatorClass IV cosmetic requirements are the least critic in the this documentExample: the inside of co
20、mputer, monitor and keyboard.4.金屬板片: SHEET METAL4.1.一般規定:GENERAL REQUIREMENTS4.1.1.電鍍表面:Plated surfaces A.電鍍附著力:起氣泡不接受,附著力不良以致裸露出金屬者,不接受.Plating adhesion Blisters are not acceptable. Improper adhesion which exposes baremetal is not acceptable. B.氧化:只有預鍍材料之剪力邊緣容許氧化( 生紅色或白色鏽),例如:如第 4.5.1-C 節規定之顏色不均勻.顏
21、色不連續(條紋、污點、斑點)可接受.Oxidation Oxidation (rust) ,red or white, is acceptable on sheared edges of preplated materials materials only (exception :see section 4.5.1-C;color uniformity) color discontinuities (streaks, stains, blotches, etc.)are acceptable.C.彎痕:每一料件容許一直徑小於 0.08 英寸之折彎痕跡,表面或邊緣脫色不接受.Arching ma
22、rks One mark per part less than 0.08 inch in diameter is acceptable.Discoloration of surface or edge in not acceptable.D.沖壓痕:正常之沖壓痕跡可接受.Stamping marks.Normal stamping marks are acceptable.NON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSMETIC,CPU/OP
23、TION PRODUCTS PAGE 8 OF 38 REVE.表面狀況:電鍍或轉化塗裝程序正常產生之輕微條痕或水漬可接受Surface phenomena Light streaking or water spotting occurring as a normal part orconversion costing process is acceptable.4.1.2.清潔度:零件應無灰塵、污垢、潤滑油、機油、鉻酸或任何其他表面沾染物,如果是搬運材料時,可吹掉或擦傷的灰塵則可接受.零件應無任何可能陷在硬體、裂縫或彎摺處或其他凹陷處的沾染物.Cleanliness Assemblies s
24、hall be free of dirt, grime, oil and other contaminants.Dust caused by shipping material is acceptable if it can be blown offwith air. Cosmetic surface shall be free of adhesive contaminants.4.1.3.烤漆面: painted surfaces .A.烤漆附著: 起氣泡不接受;附著不良以致裸露出金屬者,不接受.Paint adhesion Blisters and other signs of impro
25、per adhesion which expose bare metalare not acceptable. B.顏色均一致:烤漆面之顏色及花紋各處均一致,不同面或可容許稍有差異,但同一面則不得有任何顏色差異.Color uniformity.The color and texture of a painted surface shall be uniform. The colorand texture may vary from surface to surface. But it may vary withinthe same surface.4.2.第 I 級面: CLASS I SU
26、RFACES4.2.1.電度表面: 不適用.Plated surfaces Not applicable.4.2.2.烤漆面: Painted Surfaces. NON HAI PRECISION IND. CO. ,LTD.系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範文件編號: SPECIFCATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 9 OF 38 REVA.刮痕或磨損:刮痕或磨損以致裸露出金屬者,不接受.若直徑 152.4mm 之圓範圍內,只有一個未裸露出金屬之刮痕或磨損,且未改善表面顏色,或直徑小於
27、3.048mm 者,則可接受 .任何肉眼可見破壞花紋之條紋或清撕痕,均不接受Scratches or Abrasion.Scratches or abrasion are not acceptable if they expose bare metal. If the scratch or abrasion does not change the surface color, or is less than 3.048mmonly one (1) scratch or visible marks that repple or tear the textured surfaces are not
28、 acceptable.B.髒污 :髒污改變表面顏色,且直徑大於 0.635m/m 英寸者不予接受.Contamination Contamination that changes the surface color and exceeds. 0.635m/m in diameter is not acceptable.如直徑小於 0.254m/m 之髒污,視為看不見.任二個髒污之最小距離應為 50.8mm.Contamination less than 0.254m/m in diameter shall be considered notVisible. The minimum dista
29、nce between any two (2) particles ofContamination shall be 50.8mm.C.雜質 :直徑大於 1.016m/m 之雜質不予接受,在任何 50.8mm 之圓圈內不得有 4 個以上或任何二個距離小於 50.8mm 之雜質.Inclusions Inclusions greater than 1.016m/m in diameter are not acceptable. There shall beNo more than four (4) single inclusion within any 12.00 inch diameter c
30、ircleAnd no two (2) closer than 50.8mm.D.凹陷及壓痕:直徑大於 2.286m/m 之凹痕不予接受.任何直徑 609.6mm 之圓內不得有超過一個凹陷或條紋.Dents and slug marksDents and slug marks greater than 2.286m/m in diameter are not acceptable. There shall be no more than one (1) dent or slug mark within 609.6mm.diameter circle. NON HAI PRECISION IND
31、. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 10 OF 38 REV4.3.第 II 級面 : CLASS II SURTACES 4.3.1.電鍍表面: Plated surface A.刮傷或磨損:刮痕如果超過長 50.80.508m/m 不接受.組裝後,組裝工具造成的明顯螺旋狀刮痕,不接受.磨損直徑大於 9.652m/m 者,不予接受.在直徑 152.4mm 的圓形內,不得超過三個刮傷或一個磨損.Scratches
32、 abrasions Scratches greater than 50.8 mm long by 0.508mm wide are notacceptable. Spiral scratches caused by assembly tools are not acceptable where evident after assembly. Abrasions greater than 9.652mm indiameter are not acceptable. There shall be more than three (3) scratchesor one (1) dent or sl
33、ug mark in a 152.4mm diameter circle.B.凹陷及壓痕:超過直徑 1.27mm 之凹痕或壓痕不接受 .在直徑 152.4mm的圓形內,不得超過一個凹陷及壓痕.Dents and slug marks Dents or slug marks greater than 1.27mm in diameter are not acceptable.There shall be no more than one (1) dent or slug mark in 152.4mmdiameter circle. C.顏色均一性:輕微暈狀條紋可接受.直徑 152.4mm 的任
34、何圓形內的二個包括白色氧化所造成脫色斑點,如果不超過長 25.42.032mm 寬或直徑 6.35mm 可接受 .Color uniformity (post plated parts only) The color may vary from silverto blue Light iridescent streaking is acceptable two (2) discoloration.including those caused by white oxidation, are acceptable within any152.4mm diameter, provided they
35、are not greater than 25.4 mm long by2.032mm wide or 6.35mm in diameter.D.水漬:水漬大於 14 總表面,或連續水漬直徑大於 19.05mm 者不予接受Water spots Water spots are not acceptable if the total area they occupy is greater than14 the total surface area. Continuous water spots greater than 19.05mmin diameter are not acceptable NON HAI PRECISION IND. CO. ,LTD.文件編號: 系統名稱 SYSTEM:PCE 製造生產作業系統主 題 :SUBTEECT:CPU 外觀規範SPECIFCATION,COSMETIC,CPU/OPTION PRODUCTS PAGE 11 OF 38 REV
