1、伺服电机原理和应用Servomotors are available as AC or DC motors. Early servomotors were generally DC motors because the only type of control for large currents was through SCRs for many years. As transistors became capable of controlling larger currents and switching the large currents at higher frequencies,
2、the AC servomotor became used more often. Early servomotors were specifically designed for servo amplifiers. Today a class of motors is designed for applica-tions that may use a servo amplifier or a variable-frequency controller, which means that a motor may be used in a servo system in one applicat
3、ion, and used in a variable-frequency drive in another application. Some companies also call any closed-loop system that does not use a stepper motor a servo system, so it is possible for a simple AC induction motor that is connected to a velocity controller to be called a servomotor.Some changes th
4、at must be made to any motor that is designed as a servomotor in-cludes the ability to operate at a range of speeds without overheating, the ability to operate at zero speed and retain sufficient torque to hold a load in position, and the ability to operate at very low speeds for long periods of tim
5、e without overheating. Older-type motors have cooling fans that are connected directly to the motor shaft. When the motor runs at slow speed, the fan does not move enough air to cool the motor. Newer motors have a separate fan mounted so it will provide optimum cooling air. This fan is powered by a
6、con-stant voltage source so that it will turn at maximum RPM at all times regardless of the speed of the servomotor. One of the most usable types of motors in servo systems is the permanent magnet (PM) type motor. The voltage for the field winding of the permanent magnet type motor can be AC voltage
7、 or DC voltage. The permanent magnet-type motor is similar to other PM type motors presented previously. Figure 11-83 shows a cutaway picture of a PM motor and Fig. 11-84 shows a cutaway diagram of a PM motor. From the picture and diagram you can see the housing, rotor and stator all look very simil
8、ar to the previous type PM motors. The major difference with this type of motor is that it may have gear reduction to be able to move larger loads quickly from a stand still position. This type of PM motor also has an encoder or resolver built into the motor housing. This ensures that the device wil
9、l accurately indicate the position or velocity of the motor shaft. FIGURE 11-83 Typical PM servomotors. FIGURE 11-84 Cutaway picture of a permanent magnet servomotor. 11.11.5.1 Brushless Servomotors The brushless servomotor is designed to operate without brushes. This means that the commutation that
10、 the brushes provided must now be provided electronically. Electronic commutation is provided by switching transistors on and off at appropriate times. Figure 11-85 shows three examples of the voltage and current waveforms that are sent to the brushless servomotor. Figure 11-86 shows an example of t
11、he three windings of the brushless servomotor. The main point about the brushless servomo-tor is that it can be powered by either ac voltage or dc voltage.Figure 11-85 shows three types of voltage waveforms that can be used to power the brushless servomotor. Figure ll-85a shows a trapezoidal EMF (vo
12、ltage) input and a square wave current input. Figure ll-85b shows a sinusoidal waveform for the input voltage and a square wave current waveform. Figure ll-85c shows a sinusoidal input waveform and a sinusoidal current waveform. The sinusoidal input and sinusoidal current waveform are the most popul
13、ar voltage supplies for the brushless servomotor.Figure 11-86 shows three sets of transistors that are similar to the transistors in the output stage of the variable-frequency drive. In Fig. ll-86a the transistors are connected to the three windings of the motor in a similar manner as in the variabl
14、e-frequency drive. In Fig. 1 l-86b the diagram of the waveforms for the output of the transistors is shown as three separate sinusoidal waves. The waveforms for the control circuit for the base of each transis-tor are shown in Fig. ll-86c. Figure ll-86d shows the back EMF for the drive waveforms.FIG
15、URE 11-85 (a) Trap-ezoidal input voltage and square wave current wave-forms. (b) Sinusoidal in-put voltage and sinusoidal voltage and square wave output voltage wave-forms. (c) Sinusoidal in-put voltage and sinusoi-dal current waveforms. This has become the most popular type of brushless servomotor
16、control. Servomotor Controllers Servomotor controllers have become more than just amplifiers for a servomotor. Today servomotor controllers must be able to make a number of decisions and provide a means to receive signals from external sensors and controls in the system, and send signals to host con
17、trollers and PLCs that may interface with the servo system. Figure 11-87 shows a picture of several servomotors and their amplifiers. The components in this picture look similar to a variety of other types of motors and controllers.Figure 11-88 shows a diagram of the servomotor controller so that yo
18、u can see some of the differences from other types of motor controllers. The controller in this diagram is for a DC servomotor. The controller has three ports that bring signals in or send signals out of the controller. The power supply, servomotor, and tachometer are connected to port P3 at the bot
19、tom of the controller. You can see that the supply voltage is 115-volt AC single phase. A main disconnect is connected in series with the LI wire. The LI and N lines supply power to an isolation step-down transformer. The secondary voltage of the trans-former can be any voltage between 20 and 85 vol
20、ts. The controller is grounded at terminal 8. You should remember that the ground at this point is only used to provide protection against short circuits for all metal parts in the system.The servomotor is connected to the controller at terminals 4 and 5. Terminal 5 is + and terminal 4 is . Terminal
21、 3 provides a ground for the shield of the wires that connect the motor and the controller. The tachometer is connected to terminals 1 and 2. Terminal 2 is + and terminal 1 is . The shield for this cable is grounded to the motor case. The wires connected to this port will be larger than wires connec
22、ted to the other ports, since they must be capable of carrying the larger motor current. If the motor uses an external cooling fan, it will be connected through this port. In most cases the cooling fan will be powered by single-phase or three-phase AC voltage that remains at a constant level, such a
23、s 110 volts AC or 240 volts AC. FIGURE 11-86 (a) Tran-sistors connected to the three windings of the brushless servomotor. (b) Waveforms of the three separate voltages that are used to power the three motor wind-ings. (c) Waveforms of the signals used to control the transistor se-quence that provide
24、s the waveforms for the previous diagram, (d) Waveform of the overall back EMF. FIGURE 11-87 Example servomotors and ampli-fiers. FIGURE 11-88 Diagram of a servo controller. This diagram shows the digi-tal (on-off) signals and the analog signals that are sent to the controller, and the signals the c
25、on-troller sends back to the host controller or PLC. The command signal is sent to the controller through port PI. The terminals for the command signal are 1 and 2. Terminal 1 is + and terminal 2 is . This signal is a type signal, which means that it is not grounded or does not share a ground potent
26、ial with any other part of the circuit. Several additional auxiliary signals are also connected through port 1. These signals include inhibit (INH), which is used to disable the drive from an ex-ternal controller, and forward and reverse commands (FAC and RAC), which tell the con-troller to send the
27、 voltage to the motor so that it will rotate in the forward or reverse direc-tion. In some applications, the forward maximum travel limit switch and reverse maximum travel limit switch are connected so that if the machine travel moves to the extreme posi-tion so that it touches the overtravel limit
28、switch, it will automatically energize the drive to begin travel in the opposite direction.Port PI also provides several digital output signals that can be used to send fault signals or other information such as “drive running“ back to a host controller or PLC. Port PI basically is the interface for
29、 all digital (on-off) signals.Port P2 is the interface for analog (0-max) signals. Typical signals on this bus include motor current and motor velocity signals that are sent from the servo controller back to the host or PLC where they can be used in verification logic to ensure the con-troller is se
30、nding the correct information to the motor. Input signals from the host or PLC can also be sent to the controller to set maximum current and velocity for the drive. In newer digital drives, these values are controlled by drive parameters that are programmed into the drive.PWM Servo Amplifier The PWM
31、 servo amplifier is used on small-size servo applications that use DC brush-type servomotors. Figure 11-89 shows a diagram for this type of amplifier. From the diagram you can see that single-phase AC power is provided to the amplifier as the supply at the lower left part of the diagram. The AC volt
32、age is rectified and sent to the output section of the drive that is shown in the top right comer of the diagram. The output section of the drive uses four IGBTs to create the pulse-width modulation waveform. The IGBTs are con-nected so that they provide 30-120 volts DC and up to 30 A to the brush-t
33、ype DC servo-motor. The polarity of the motor is indicated in the diagram.The remaining circuits show a variety of fault circuits in the middle of the diagram that originate from the fault logic board and provide an output signal at the bottom of the diagram. You should notice that the fault output
34、signals include overvoltage, overtempera-ture, and overcurrent. A fourth signal is identified as SSO (system status output), which in-dicates the status of the system as faulted anytime a fault has occurred. A jumper is used to set the SSO signal as an open collector output with a logic level “1“ in
35、dicating the drive is ready, or as a normally closed relay indicating the drive is ready.The input terminals at the bottom right part of the diagram are used to enable or inhibit the drive, and to select forward amplifier clamp (FAC) or reverse amplifier clamp (RAC). The inhibit signal is used as a
36、control signal, since it inhibits the output stage of the amplifier if it is high. The FAC and RAC signals limit the current in the opposite direction to 5%.The input signals are shown in the diagram at the upper left side. The VCS (velocity command signal) requires a +VCS and a -VCS signal to provi
37、de the differential signal.Applications for Servo Amplifiers and Motors You will get a better idea of how servomotors and amplifiers operate if you see some typical applications. Figure 11-90 shows an example of a servomotor used to control a press feed. In this application sheet material is fed int
38、o a press where it is cut off to length with a knife blade or sheer. The sheet material may have a logo or other advertisement that must line up registration marks with the cut-off point. In this application the speed and po-sition of the sheet material must be synchronized with the correct cut-off
39、point. The feed-back sensor could be an encoder or resolver that is coupled with a photoelectric sensor to determine the location of the registration mark. An operator panel is provided so that the operator can jog the system for maintenance to the blades, or when loading a new roll of material. The
40、 operator panel could also be used to call up parameters for the drive that cor-respond to each type of material that is used. The system could also be integrated with a programmable controller or other type of controller and the operator panel could be used to select the correct cutoff points for e
41、ach type of material or product that is run.FIGURE 11-89 Diagram of a pulse-width modulator (PWM) amplifier with a brush-type DC servomotor. FIGURE 11-90 Appli-cation of a servomotor controlling the speed of material as it enters a press for cutting pieces to size. 11.11.8.1 An Example of a Servo Co
42、ntrolled In-Line Bottle-Filling ApplicationA second application is shown in Fig. 11-91. In this application multiple filling heads line up with bottles as they move along a continuous line. Each of the filling heads must match up with a bottle and track the bottle while it is moving. Product is disp
43、ensed as the nozzles move with the bottles. In this application 10 nozzles are mounted on a carriage that is driven by a ball-screw mechanism. The ball-screw mechanism is also called a lead screw. When the motor turns the shaft of the ball screw, the carriage will move horizontally along the length
44、of the ball-screw shaft. This movement will be smooth so that each of the nozzles can dis-pense product into the bottles with little spillage.The servo drive system utilizes a positioning drive controller with software that allows the position and velocity to be tracked as the conveyor line moves th
45、e bottles. A master encoder tracks the bottles as they move along the conveyor line. An auger feed system is also used just prior to the point where the bottles enter the filling station. The auger causes a specific amount of space to be set between each bottle as it enters the filling station. The
46、bottles may be packed tightly as they approach the auger, but as they pass through the auger their space is set exactly so that the necks of the bottles will match the spacing of the filling nozzles. A detector is also in conjunction with the dispensing system to ensure that no product is dispensed from a nozzle if a bottle is missing or large spaces appear between bottles.
