美国标准-钛及钛合金.doc

上传人:sk****8 文档编号:3515505 上传时间:2019-06-01 格式:DOC 页数:30 大小:476KB
下载 相关 举报
美国标准-钛及钛合金.doc_第1页
第1页 / 共30页
美国标准-钛及钛合金.doc_第2页
第2页 / 共30页
美国标准-钛及钛合金.doc_第3页
第3页 / 共30页
美国标准-钛及钛合金.doc_第4页
第4页 / 共30页
美国标准-钛及钛合金.doc_第5页
第5页 / 共30页
点击查看更多>>
资源描述

1、成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02887442868 87457545 传真;028-87482878 1美国标准-钛及钛合金,棒和丝材(英文)Standard Specification for Tantalum and Tantalum Alloy Rod and WireThis standard is issued under the fixed designation B 365;the number immediately following the designation indicates the year of original adoption or,

2、in the case of revision, the year of last revision. A number in parentheses in dicates the year of last reaproval. A superscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers unalloyed and alloyed tantalum rod and wire.1.2 The mate

3、rials covered by this specification are:1.2.1 R05200,unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both,1.2.2 R05400,unalloyed tantalum, powder-metallurgy consolidation,1.2.3 R05255,tantalum alloy,90% tantalum 10% tungsten, electron-beam furnace or vacuum-arc meal, or both,1.2.4 R

4、05252,tantalum alloy 97.5% tantalum 2.5% tungsten, electron-beam furnace or vacuum-arc melt, or both,1.2.5 R05240 tantalum alloy ,60% tantalum 40% columbium ,electron-beam furnace or vacuum-arc melt ,or both.1.3 The values stated in inch-pound unties are to be regarded as the standard .The values gi

5、ven in parentheses are for information only.1.4 The following precautionary caveat pertains only to the test methods portion ,Section 13,of this specification: This standard does not purport to address all of the safety problems ,if any, associated with its use, It is the 成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02

6、887442868 87457545 传真;028-87482878 2responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:B 364 Specification for Tantalum and Tantalum Alloy In

7、gotsE 8 Test Methods for Tension Testing of Metallic MaterialsE 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications3. Terminology3.1 Descriptions of Terms Specific to This Standard:3.1.1 lot all material produced from the same ingot or a single powder b

8、lend at one time, with the same cross section and with the same nominal metallurgical parameters.3.1.2 rod-material 0.125 to 2.5 in.(3.18 to 63.50mm)in diameter in round ,hexagonal, or octagonal cross section supplied in straight lengths.3.1.3 wire-material 0.010 to 0.124 in.(0.254 to 3.15mm)in diam

9、eter furnished in coils or on spools or reels. Material less than 0.010 in . in diameter is not covered by this specification.4.Ordering Information4.1 Orders for material under this specification shall include the following information as applicable:4.1.1 Quantity (weight or number of pieces),4.1.2

10、 Name of material (tantalum rod or wire),成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02887442868 87457545 传真;028-87482878 34.1.3 Type(see 1.2)4.1.4 Method of manufacture (Section 5),4.1.5 ASTM designation,4.1.6 Finish and appearance(Section 9) ,and4.1.7 Additions to the specification and supplementary requirements if

11、required.5. Materials and Manufacture5.1 Material covered by this specification shall be made from vacuum-arc melted or electron-beam melted ingots or powder-metallurgy consolidated unalloyed tantalum conforming to Specification B 364.5.2 The Various tantalum mill products covered by this specificat

12、ion are formed with the conventional extrusion, forming , swaging ,rolling ,and drawing equipment normally available in metal working plants.6. Chemical Composition6.1 The tantalum and tantalum alloy ingots and the tantalum powder-metallurgy consolidated ingots for conversion to finished products co

13、vered by this specification shall conform to the requirements for chemical composition as prescribed in Table 1.6.1.1 Analysis for elements not listed in Table 1 and not normally expected in tantalum shall not be required unless specified at time of purchase.6.2 The manufacturers ingot analysis shal

14、l be considered the chemical analysis for products supplied under this specification.6.3 When requested by the purchaser at the time of purchase, the seller shall furnish a report certifying the values Table 2 for each 成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02887442868 87457545 传真;028-87482878 4lot of material su

15、pplied. The performance of this special provision will be negotiated.7. Mechanical Properties7.1 Materials supplied under this specification shall con-form to the requirements for mechanical properties as specified in Table 3.TABLE 1 Chemical RequirementsContent,max,weight %ElementElectron-BeamCast(

16、R05200)Vacuum-Arc Cast(R05200)UnalloyedTantalumSintered(R05400)UnalloyedTantalumElectron-BeamCast(R05255)Vacuum-Are(Cast(R05255)90%Tantalum 10%TungstenElectron-BeamCast(R05255)Vacuum-Are(Cast(R05252)97.5%Tantalum 2.5%TungstenElectron-BeamCast(R05240)Vacuum-Are(Cast(R05255)60%Tantalum 40%ColumbiumC 0

17、.010 0.010 0.010 0.010 0.010O 0.015 0.03 0.015 0.015 0.020N 0.010 0.010 0.010 0.010 0.010H 0.0015 0.0015 0.0015 0.0015 0.0015Nb 0.10 0.10 0.10 0.50 35.0-42.0Fe 0.010 0.010 0.010 0.010 0.010Ti 0.010 0.010 0.010 0.010 0.010W 0.050 0.050 9.0-11.0 2.0-3.5 0.050Mo 0.020 0.020 0.020 0.020 0.020Si 0.005 0.

18、005 0.005 0.005 0.005Ni 0.010 0.010 0.010 0.010 0.010Ta remainder remainder remainder remainder remainder7.2 he performance of mechanical tests to this requirement will be negotiated at time of purchase.成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02887442868 87457545 传真;028-87482878 58. Dimensions, Mass, and Permissib

19、le Variations8.1 Tolerances on RoundsTolerances on tantalum and tantalum alloy round products covered by this specification shall be as specified in Table 4.8.2 Tolerances for Square, Rectangular, or Other ShapesTolerances for forged or rolled square, rectangular, or other shapes shall be as agreed

20、upon between purchaser and seller at the time of purchase.8.3 Other Tolerances and Limitations:8.3.1 The permissible variation in cut lengths shall not exceed a total of 0.25 in.(6.35mm).8.3.2 The permissible variation in straightness of rounds shall not exceed 0.050 in.(1.27mm)/ft(304.8mm)in any le

21、ngth.8.4 Quantity or Weightfor orders requiring up to 100 lb(45.4kg),the manufacturer may overship by 10%. When the order is for quantities up to 500 lb(226.8kg),the manufacturer may overship by 5%.The permissible overship for quantities larger than this shall be negotiated between the purchaser and

22、 the manufacturer.9. Workmanship, Finish, and Appearance9.1 The finished rod and wire shall be free of injurious external and internal imperfections of a nature that will interfere with the purpose for which it is intended in accordance with standards of acceptability agreed upon between the manufac

23、turer and the purchaser.9.2 material may be finished as forged, rolled, swaged, drawn in the as-cleaned, as-machined, or as-ground conditions. The manufacturer shall be permitted to remove minor surface imperfections provided such removal does not reduce the dimensions below the minimum permitted by

24、 the tolerances established in Section 8 of this specification.成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02887442868 87457545 传真;028-87482878 69.3 Methods of testing for defects and standards of acceptability shall be as agreed upon between the manufacturer and the purchaser at time of purchase.10. Significance of N

25、umerical Limits10.1 For the purpose of determining compliance with the specified limits for requirements on the properties listed in this specification, observed and calculated values shall be rounded as indicated by the rounding method of Practice E 29.11. Sampling11.1 Samples shall be taken from t

26、he material to determine conformity to this specification. The samples shall be taken so as to be representative of the finished products.11.2 Care shall be taken to ensure that the sample selected for testing is representative of the material, and that it is not question relating to the sampling te

27、chnique, or to the testing there of, the methods of sampling and testing shall be as agreed upon between the purchaser and the manufacturer.12. Number of Tests12.1 if mechanical testing is required(7.2), perform a longitudinal or transverse tension test on each lot of and a longitudinal tension test

28、 on each lot of wire.TABLE 2 Additional Chemical requirements for Finished product(When Specified by the Purchaser)Content, max,% weight GradesElementElectron-Beam Case(R05200)Vacuum-Arc Cast(R05200)Sintered(R05400)UnalloyedTantalumElectron-Beam Cast(R05255)Vacuum-Arc Cast(R05255)Electron-Beam Cast(

29、R05252)Vacuum-Arc Cast(R05252)Electron-Beam Cast(R05240)Vacuum-Arc Cast(R05240)成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02887442868 87457545 传真;028-87482878 7UnalloyedTantalum90% Tantalum10% Tungsten97.5% Tantalum2.5% Tungsten60% Tantalum40% TungstenO 0.025 0.035 0.025 0.025 0.025N 0.010 0.010 0.010 0.010 0.010H 0.

30、0015 0.0015 0.0015 0.0015 0.0015C 0.020 0.020 0.020 0.020 0.020TABLE 3 Mechanical Properties for Rod and Wire, Annealed ConditionRod 0.125 in.(3.18mm)to 2.5 in.(63.5mm) DiameterUltimate Tensile Strength,min,psi(MPa)Yield Strength,Min,psi(MPa)Elongation,min,%1 in.(25.4mm)Gage LengthUnalloyed tantalum

31、(R05200 and R05400)97.5% tantalum 2.5% tungsten(R05252)90% tantalum 10% tungsten R0525560% tantalum 40% columbium(R05240)25 000(17240 000(276)70 000(482)40 000(276)15 000(103)28 000(193)55 000(379)28 000(193)25202025Diameter, in.(mm)Ultimate TensileStrength, min, psi(MPa)ElongationMin,%AUnalloyed ta

32、ntalum(R05200 and R05400)0.010(0.254) to 0.0149 (0.379)0.015(0.381) to 0.0249 (0.633)0.025(0.635) to 0.124(3.14)35 000(241)35 000(241)30 000(207)10152097.5% tantalum 2.5% tungsten (R05252)0.010(0.254) to 0.0149 (0.379)0.015(0.381) to 0.0249 (0.633)0.025(0.635) to 0.124(3.14)40 000(276)40 000(276)40

33、000(276)5101590% tantalum 10% tungsten(R05255)0.010(0.254) to 0.0149 (0.379)0.015(0.381) to 0.0249 (0.633)0.025(0.635) to 0.124(3.14)70 000(482)70 000(482)70 000(482)5101560% tantalum 40% tungsten(R05240)0.010(0.254) to 0.0149 (0.379) 40 000(276) 10成都洛克钛业有限公司成都市机投桥业兴北路 9 号 02887442868 87457545 传真;02

34、8-87482878 80.015(0.381) to 0.0249 (0.633)0.025(0.635) to 0.124(3.14)40 000(276)40 000(276)1520A 10-in.(254-mm)gage length to 0.050 in.(1.27-mm)diameter and 1-in.(25.4-mm)or 2-in.(50.8-mm)gage length over 0.050-in.(1.27-mm)diameterTABLE 4 Permissible Variations in Dimensions for Rolled, Swaged or Dr

35、awn Rod and WireDiameter,in.(mm) Tolerance,in.(mm)0.010 to 0.020 excl(0.254 to 0.508) 0.0005(0.013)0.020 to 0.030 excl (0.508 to 0.762) 0.00075(0.019)0.030 to 0.060 excl(0.762 to 1.524) 0.001(0.025)0.060 to 0.090 excl(1.524 to 2.286) 0.0015(0.038)0.090 to 0.125 excl(2.286 to 3.175) 0.002(0.051)0.125

36、 to 0.187 excl(3.175 to 4.750) 0.003(0.076)0.187 to 0.375 excl(4.750 to 9.525) 0.004(0.102)0.375 to 0.500 excl(9.525 to 1.524) 0.005(0.127)0.500 to 0.625 excl(12.70 to 15.88) 0.007(0.178)0.625 to 0.750 excl(15.88 to 19.05) 0.008(0.203)0.750 to 1.000 excl(19.05 to 25.40) 0.010(0.254)1.000 to 1.500 ex

37、cl(25.40 to 38.10) 0.015(0.381)1.500 to 2.000 excl(38.10 to 50.80) 0.020(0.508)2.000 to 2.500 excl(50.80 to 63.50) 0.030(0.762)12.2 If end-product chemical tests are required(6.3), make one chemacal test from each lot of finished product.13. Test Methods13.1 Tension Testsprepare and test specimen in

38、 accordance with Test Methods E 8. Determine tensile properties using a strain rate of 0.003 to 0.007 in./(in. min) to the yield point and 0.02 to 0.05 in./(in. min) to failure.13.2 Chemical TestsConduct the chemical analysis in accordance with established methods.成都洛克钛业有限公司成都市机投桥业兴北路 9 号 0288744286

39、8 87457545 传真;028-87482878 913.3 RetestsIf any sample or specimen exhibits obvious surface contamination or improper preparation disqualifying it as a truly representative sample, discard it and substitute a new sample or specimen.13.3.1 In case of a failure, retest two additional specimens . If bot

40、h retest specimens conform to this specification, discard the original values and consider the material acceptable.13.3.2 If the results of the tests are not in conformance with the requirements of this specification, a lot may be reworked at the option of the manufacturer. The lot shall be acceptab

41、le if results of all tests, after reworking, conform to this specification.14. Inspection14.1 The manufacturer shall inspect the material covered by this specification prior to the shipment.14.2 If so specified on the purchase order, the purchaser or his representative may witness the testing and in

42、spection of the material at the place of manufacture . In such cases, the purchase order shall indicate which test or tests to be witnessed and the manufacturer shall give ample notice to the purchaser as to the time and place of the designated test. If the purchasers representative does not present

43、 himself at the agreed-upon time for the testing, and if no new date is agreed upon, the manufacturer shall consider the requirement for purchasers inspection at place of manufacture to be waived. When the inspector representing the purchaser does appear at the appointed place and time, the manufact

44、urer shall afford him, without charge, all reasonable facilities to see that the material is being furnished in accordance with this specification. This inspection shall be conducted so as not to interfere unnecessarily with production operations.15. Rejection and Rehearing15.1 Material that fails t

45、o conform to the requirements of this specification may be rejected. Rejected. Rejection should be reported to the producer or supplier promptly and in writing. In case of dissatisfaction with the results of the test, the producer or supplier may make claim for a rehearing.16. Referee成都洛克钛业有限公司成都市机投

46、桥业兴北路 9 号 02887442868 87457545 传真;028-87482878 1016.1 In the event of disagreement between the manufacturer and the purchaser of the conformance of the material to the requirements of this specification or any special test specified by the purchaser, a mutually accepted referee shall perform the tes

47、ts in question. The results of the referees testing shall be used in determining conformance of the material to this specification.17. Reports17.1 If requested, the manufacturer shall supply at least three copies of a report of the chemical analysis and reports of the results of tests of representat

48、ive finished product to determine properties required in Section 13. The reports should include the purchase order number, this specification number, and the quantity and number of items covered in the shipment and a statement that the material was manufactured, sampled, tested, and inspected in acc

49、ordance with the specific.Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate This standard is issued under the fixed designation B 265; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision A number in parentheses indicates the year of last reapproval. A superscript epsilon()indicates an editorial change since the last re

展开阅读全文
相关资源
相关搜索

当前位置:首页 > 实用文档资料库 > 策划方案

Copyright © 2018-2021 Wenke99.com All rights reserved

工信部备案号浙ICP备20026746号-2  

公安局备案号:浙公网安备33038302330469号

本站为C2C交文档易平台,即用户上传的文档直接卖给下载用户,本站只是网络服务中间平台,所有原创文档下载所得归上传人所有,若您发现上传作品侵犯了您的权利,请立刻联系网站客服并提供证据,平台将在3个工作日内予以改正。