1、Doc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 1/14未經許可,禁止複製Outgoing Inspection Criteriaforxxx LCD MonitorPrepared: _Checked: _Approved: _QA PD PE RD分發單位 Doc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 2
2、/14未經許可,禁止複製Revision History Revision Change Revised Pages Date Comments1.0 InitialDoc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 3/14未經許可,禁止複製1. 適用範圍 Scope 本指导书适用于達裕电子公司生产出厂的 M9T 成品出厂检查。This document shall be used in conjunction with outgoing inspect
3、ion of LCD monitor assembled by TechView.2. 抽樣計畫 Sampling Plan 依據 MIL-STD-105E , Level-II , 隨機抽樣 , 除非有特別規定 , 一般皆使用單次 ,正常檢驗 .檢查判定標準之定義 :According to MIL-STD-105E, Level-II, Normal signal samplinga) Critical “嚴重缺點“ ：又稱安全缺陷,系指有危害産品的銷售或使用者的生命, 安全之缺陷,或不符合銷售地區之安全規格或最終産品不能執行或使用(如 Dead On Arrival) 。The crit
4、ical defect is defect that judgment and experience indicate would result in hazardous or unsafe conditions for individuals using, maintaining, or depending upon the product, or a defect that judgment and experience indicate is likely to prevent performance of critical function of a major end item.b)
5、 Major “主要缺點 “ ：係指除嚴重不合格外,産品單位的使用性能不能達到所期望之目的或顯著的降低其實用性的不合格。The major defect is a defect that is likely to result in product failure, or reduction in the products intended usage.c) Minor “次要缺點 “ ：係指對産品單位的使用性能,可能不致减低或難與規格完全相符, 但在使用和操作使用上幷無影響者。The minor defect is a defect that has little bearing on th
6、e effective use or Operation of the product.3. 品質允收水準 AQL level以 Critical=0 Major = 0.4 % , Minor = 1.0% 判定4. 測試條件 Test Condition 4.1 環境溫度 Ambient temperature25 5 0CDoc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 4/14未經許可,禁止複製4.2 電源輸入 AC voltage依出貨地區所適
7、用之電源設定 (適用範圍:100 240 Vac, 47/63 Hz).According the destination to set up input voltage 100-240 Vac 47/63 Hz4.3 輸入信號電平 Input signal level0.7 Vp-p5. 測試設備 Test equipment a) 圖形產生器 Signal Generator The reference signal source is a calibrated Chroma 2327. The use of other signal generators during qualifica
8、tion and production is acceptable provided the product complies with this specification.b) 色彩分析儀 Photometric Measurements All photometric measurements shall be made with a Minolta CA-210 test instrument. The calibration of the test instrument used shall be traceable to an NBS source. The use of othe
9、r equipment for qualification and production is acceptable, provided appropriate offsets are applied so that the monitor meets this specification when measured with the CA-210 as specifiedc) 功率計 Power Meter The reference power meter is a calibrated IDRC CP-310. The use of other signal generators dur
10、ing qualification and production is acceptable provided the product complies with this specification.d) Personal Computer IBM compatible PC Windows 98 or abovee) 交流電源供應器 AC Power Source f) 放大鏡 Microscope 25xg) 濾光片 ND Filter with 8%, 5%h) 面積規 Dimension measurement filmi) 厚薄規 Thickness gaugej) 敲擊棒 Tap
11、per6. 檢驗項目 Inspection itemDoc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 5/14未經許可,禁止複製6.1 包裝檢驗 Packing項次Item檢驗項目Inspection檢驗規格Specification CRI MAJ MIN備註Remark不潔 Dirty 3 cm2 1 cm2 破損 Broken 10 mm 印刷錯誤或印刷不良(拼字錯誤,字型與字體大小不同)Incorrect or poor printing顏色錯誤
12、或色差Incorrect color or chromatism 1 紙箱Carton box尺寸錯誤(太大或太小)Wrong dimensions of carton 和內部物品無法適當配合not match with cushion properly5cm 2 layersOverlaps 貼附位置不正確Incorrect position 傾斜 Tilt 3 印刷內容錯誤 Wrong printing 印刷模糊 Blurred 無法以掃描槍讀取條碼Unreadable by scanner 3 紙箱條碼標簽Barcode label掉落 Fall off 缺少(漏裝) Missing 多
13、出 Extra 錯誤 Wrong part 4附件Accessory擺放方式錯誤 Improperly pack 錯誤 Wrong parts 印刷不良 Poor printing 5 說明書Users manual 缺頁或內容錯誤lack some pages 6 保利龍Cushion 破損 Broken 2cm Doc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 6/14未經許可,禁止複製斷裂 1/3 以上.而失去保護作用Crack over 3/1
14、of length and no protect function缺少 Missing 破損或陳舊 Dirty or broken 7 塑膠袋Bag 無環境標誌 without environment regulation mark 錯誤 Wrong part 長度錯誤 Wrong length 破損/割傷 Broken/Scratch內部導線裸露 wire exposed 8電源線Power cord油脂和污垢 Dirty or pollution 錯誤 Wrong part 割傷 Scratch 9 音頻線Audio cable油脂和污垢 Dirty or pollution 包裝方式違反
15、作業指導書規定,影響出貨品質 Improperly pack which may impact to quality機型錯誤 Wrong configuration 潮濕 Wet 10 其他Others箱內異物 Foreign material 6.2 外觀檢驗 Cosmetic項次Item檢驗項目Inspection檢驗規格Specification CRI MAJ MIN備註Remark與外箱流水號碼不一致Inconsistent S/N between box and monitor污損 Dirty 機種名稱錯誤Wrong model no 內容錯誤(字型,字體)Wrong or poo
16、r printing 有未通過認證之安規標誌 The regulation is not apply yet 印刷模糊 Blurred 無法以掃描槍讀取條碼Unreadable by scanner 黏貼不平整、貼反、貼錯位置 Uneven, Reverse 1 銘板標籤ID Label傾斜 Tilt 0.5mm Doc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 7/14未經許可,禁止複製污損 Dirty 溢墨或模糊不清 Blurred 偏移 Shift
17、 0.5mm 2 Logo / 印刷 Printing顏色錯誤 Wrong color破損/割傷 Broken/Scratch內部導線裸露 wire exposed 針彎曲,倒下或內縮Pin bent or dent 針錯誤(或多,或少)Pin missing or extra 油脂和污垢 Dirty or pollution 3 信號線Video cable信號線長度錯誤Wrong length 外緣毛邊 BurrA&B 區 0.1mmC 區 0.15mm刮傷 Scratch 凹 陷 Dent 流痕,縮水,气泡,結合線Parting line, shrink, bubble 裂痕(斷裂) C
18、rack 4塑膠/金具類外觀Appearance of plastic and metal污點 Spot 參考 6.2.2 塑膠/金具類外觀標準Reference to Section 6.2.2前後殼,底座色差比:E 1.0Discolor between front bezel, back cover and base5 色差 Chromatism色板顏色與咬花樣式不合 6 面板外觀 Appearance of LCD PanelScratch, Lint, Fiber, Spot, Foreign material, Dent, Air bubble.參考 6.2.3 面板外觀判定標準R
19、eference to section 6.2.36.2.1 外觀污點檢查定義 Definition of appearanceA 區 : 經組裝後位於使用者正面之區域.A zone: Font point view of monitorB 區 : 經組裝後位於使用者上面,兩側與底座上面之區域.B zone: Top and side point view of monitor and top of stand baseC 區 : 經組裝後位於使用者後面之區域.C zone: Back side view of monitorD 區 : 經組裝後必須從下方才能觀測的到之區域.D zone: B
20、ottom side of monitorDoc. no：OIC-xxx-001Date ：TechviewOutgoing Inspection CriteriaFor xxx LCD Monitor Rev： 1.0 Page： 8/14未經許可,禁止複製B 面 D 面 A 面 B 面 C 面 B 面 C 面 6.2.2 塑膠/金具類外觀標準 Appearance criteria of plastic and metal如超出此規格依 NG 判定論 Judge as reject if over limit區域 Zone項目Item直徑 /長度/寬度/深度 /L/W/D A B C D
21、Remark0.5 mm N = 00.2D0.5mm N = 4Spot,Foreign material, Dent, Air bubble. D7mm N = 0W0.1mm N = 00.01mm 1.5mmBetween front bezel and back cover1 間隙 Gap前框與 Panel 間隙 1.2mmBetween front bezel and panel 2 斷差 Alignment後蓋與前框斷差 0.8mmMis-alignment between front bezel and back cover不允許後殼高於前框Its not allowed that back cover higher than bezel缺斷 Missing or Broken 規格錯誤 Wrong type of screw 滑牙 Stripped 3 螺絲 Screw未鎖到位 Not in place
